※We recommend to use mounting brackets at intervals of 0.3 to 0.5m.※ For Kinetic TokiLeds, dimmers cannot be used.CL-B-WM-1.25mAdhesive tape attached mounting track (L=1.25m)Fixed length : 1.25m ※Can be cut on job siteLS2-EPLead wire extension processingUp to 10m (Processing length unit : 1m)LS2-WTANBoth ends lead wire attachment processingAttach a 0.5m of lead wire to each sideLS_-ED10End caps (10 pcs/set)The color code C: clear or W: white is entered in the underbarOne spare end cap per run is included for each Tapelight303030303030= Luminous MaterialΦ6Φ519181313Length = LED spacing x # of LEDs70505070LED Spacing(For 30mm LED spacing, L = LED spacing x # of LEDs + 20)500Φ8.520131.25mm2×2TP-03/20TP-01/20WM1211TL2-EPUp to 10m (Processing length unit : 1m)TL2-WTANAttach a 0.5m of lead wire to each sideTLP-ED10One spare end cap per run is included for each Tapelight5070Φ7.5LED Spacing1913(For 30mm LED spacing, L = LED spacing x # of LEDs + 20)Length = LED spacing x # of LEDsMounting bracket for mounting track (20pcs/set)Mounting bracket (20pcs/set)Adhesive tape (Strong, L=11m, W=12mm)Lead wire extension processingBoth ends lead wire attachment processingEnd caps (10 pcs/set)TapelightPower supply5001.25mm2×2(mm)The mounting track ensures linear integrity.Ultra-Bright TokiLedsAWG14 12mMounting Bracket (TP-03)Mounting TrackUse Mounting Brackets at intervals of 0.3 to 0.5m.Standard TokiLeds & Kinetic TokiLedsAWG14 17mIt is possible to connect the lighting fixtures and a remotely set power supply with an appropriate lead wire. Refer to the table for lead wire sizes and length limitation.The extension distance is a guideline distance for the fixture's maximum capacity. Depending on the type of power supply, lead wire, and number of LEDs, it may be possible to extend it further. Please contact us for more information.Mounting Brackets (TP-01) used with Adhesive tape ensure secure mounting. The proper quantity and positioning of brackets is determined by the specifics of each application. When turning corners, a device should be used at the start of each bend.When Adhesive tape or screws can not be used, a commercially available silicone may be used.Using Adhesive tape for temporaryfixing makes installation easier andprovides strength.TapelightSiliconeSealantAdnesive TapeStandard TokiLeds & Kinetic TokiLeds(mm)These dimensions are the required minimum for installation in a confined space to ensure there is not excessive heat buildup. In an actual installation, and in consideration of maintenance we recommend a wider opening while keeping these dimensions as a guideline. Conditions are different when fixtures are placed side by side.7PRODUCT GUIDEStandard TokiLeds & Kinetic TokiLedsInstallation parts (For both Outdoors and Indoors)LS Tapelight (For Outdoors)OutdoorsIndoorsUltra-Bright TokiLedsUltra-Bright TokiLedsTLP Tapelight (For Indoors)OutdoorsIndoorsLinear applicationsInstallation with Adhesive tapesRecommended Lead Wire Size and Length LimitationRecommended for use with Mounting BracketsAttach Tapelight to the track with adhesive tape. Affix the Mounting Track and Brackets with commercially available 4mm Φ screws.Adhesive tape alone can be provided sufficient mounting strength when aligning upwards on flat places, but for permanent installation, please use Mounting Brackets together. Be sure to use Mounting Brackets when mounting to walls or ceilings.The distance from the power supply to the fixture, and the load of the fixture, will determine the proper size of secondary wire. Fixtures require an individual lead. If additional wire needs to be attached, refer to the recommendation in this chart.Curved applicationsWhen Adhesive tape and screws cannot be usedPRODUCT GUIDE8Minimum Space RequirementsSpecificationsOptionsProduct CompornentInstructions
元のページ ../index.html#5