(mm)661261161072625LDRCC-40-NSLED DriverLDRCC-40-NSLED DriverLDRCC-40-NSLED DriverEach run of OLS requires this feed connector with a 2m lead.The End Connector insulates a female connector at the end of a run and completes the circuit.Extension cables extend the distance between fix-tures and may be added to OLS-CON connector to reach remote LED driver locations.OLS-CON-2m/ECOLS Lead Cable 2m & End ConnectorOLS-EXT-1mOLS-EXT-5mOLS-EXT-10mOLS Extension Cable 1mOLS Extension Cable 5mOLS Extension Cable 10mSecurely mount fixtures using screws on all four mounting holes.Each fixture is fitted with adjustable brackets on the ends.This aluminum stake will be fastened on OLS adjust-able brackets at the factory.※ The indicated angle above is for our standard extrusion. Refer to the dimensioned drawings on pages 5 and 6 for the range adjustment of various louvers.OLS-1-SPI-OPOLS-3-SPI-OP90°OLS Stake for 1-LED typeOLS Stake for 3-LED type90°LDRCC-40-NSLED DriverOur constant current LED Driver accepts input from 0-10VDC dim-ming controls. The driver has full range dim-to-off capability.The input is universal ranging from 100 to 277VAC 50/60 Hz. Up to 30 LDRCC-40-NS LED Drivers can be connected in series from a single 0-10 VDC source. The maximum distance from the 0-10VDC source to the last LED driver is 75 meters based upon the use of AWG18 shielded cable.For applications operating from DMX, Dali or other protocols, check with the dim-mer manufacturer to provide a suitable interface to generate a 0-10VDC signal.Recommended Lead Wire Size and Length LimitationThe distance from the power supply to the fixture, and the load of the fixture, will determine the proper size of secondary wire. Fixtures require an exclusive lead. If additional wire needs to be attached, refer to the recommendation in this chart.1. Read all instructions completely before beginning installation.2. Turn off electricity before beginning installation.3. All wiring is to be performed by a qualified electrician.Additional Secondary WireSpliceLength LimitationOLS Lead Cable100-277VAC100-277VAC100-277VACFixturesDimmer0-10VDC SourceSignal4. Installation must comply with the National Electrical Code, or all applicable codes.5. Turn main supply to LED Driver on only after all connections have been made and tested. 6. Use only LED Drivers provided by Tokistar with the system.LDRCC-40 SpecificationsInput Range : 100~277VACFrequency Range : 50/60 HzOutput : 3-57VDCCurrent : 700mAMax. Output Power : 40WProtection : Overload, Overcurrent, Short CircuitOver Temperature : Mis-Wiring protection (auto shutdown)Operating Temperature : -40°C to +50°CMechanical SpecificationsDimensions : 126 x 66 x 25mmWeight : 170gEnclosure Rating : IP21Mounting : Flange MountInput/Output Connectors : Wago 253/AWG16-20Safety StandardsListed to UL8750, UL Class 2, Class PEMI Compliance : FCC 47CFR Part 15 Class BLED CapacityLDRCC-40-NS : 2 to 18 OLS (2.1 Watt) LEDsLDRCC-40-NS-D : 1 OLS (2.1 Watt) LEDOLS Lead Cable700mAFixturesSignal700mAFixturesSignal700mAFixturesWire SizeAWG18 + OLS Lead Cable + FixtureEnd ConnectorTotal LengthWithin 90m7PRODUCT GUIDEOLS-CON-2m/EC (2m length)OLS-EXT-1m (1m length)OLS-EXT-5m (5m length)OLS-EXT-10m (10m length)REQUIREDPRECAUTIONSPRODUCT GUIDE8OLS ConnectorsWater proof connectors link fixtures and bring 700mA to the system for plug-and-go simplicity.MountingAdjustable bracketsMounting StakeLDRCC-40-NS(-D)Dimming ControlOLS ConnectorsInstructionPower SupplyWiring Diagram
元のページ ../index.html#5